GREEN DRAGON PRICE LIST Effective May 1,2017
Disassembly / Reassembly Is always on top of the
Cerakote coating prices. It usually ranges between $25 – $65 depending on the Gun and difficulty. Call for accurate pricing.
We have a $50.00 Minimum.
Cerakote colors that we do not normally stock will add
an additional $35 to your order.
HANDGUNS:
Complete – One Color $200.00
Complete – Two Colors $225.00
Complete – Three Color $250.00
Complete – Custom design up to 3 color $250.00 + Add
stenciled charge below
Add Camo pattern (Three colors) $60.00
4 Color Kryptek pattern Complete + up to 2 mag bases
$290.00 +Detail Stencil
3 Color SnakeSkin pattern Complete + up to 2 mag bases
$250.00 +Detail Stencil
Distress Add- $30.00
Slide Only – One Color (stripped) $40.00
Frame Only – One Color (stripped) $60.00
Coat Barrel Only with Cerakote DFAC (Includes barrel
bushing on 1911’s) $50.00
Coat Pistol Magazines – Each (must be one of the
colors on gun) $15
Coat Pistol Magazine – Separate Color $20
Stenciling work (i.e. lettering small insignias or
logo) – $20.00 Surcharge
Extreme Detail Stencil work i.e. Kryptek, Snake skin)
– $60.00 Surcharge
Hardware Only – $25.00
Add Clear ( Hi-Gloss or Matte )- $30.00
Polish Barrel – $50.00
Theme type pistols usually run around $200.00 to
$250.00 and up depending on number of colors and detail
RIFLES & SHOTGUNS:
Autoloading – AR-15/M4 or AK
Complete Gun: Upper and Lower Receivers, Barrel,
Handguard, Pistol Grip, Pins, and Controls.
( Does NOT Include stock — except on shotgun )
One Color $200.00
Two Colors $225.00
Shotgun Metal Only $145.00 Barrel only $75
Three Color Camouflage Pattern $350.00
Four Color Camouflage Patterns $375.00
Five Color Camouflage Patterns $400.00
Four Color Kryptek Pattern ( Includes the high temp
stencil ) 425.00
Camouflage Using High-Temp Stencils – Stencil
Surcharge $25.00
Coat 20/30rd AR Magazines One Color (each)
$20.00
Semi-Auto Bolt and Bolt Carrier (AR or AK) Coat with
Cerakote DFAC $50.00
Scope Mounts (One Color) $30.00
Scopes Standard – One Color C-Series $50.00
Scopes Target and Tactical – One Color C-Series
(Includes masking of dials, etc) $75.00
Scopes Target and Tactical – Camouflage (costs may
vary – call for quote) $125 – $200
ACCESSORIES
AR Upper and Lower Receivers Only – One Color
(Stripped) $110.00
Upper Only or Lower Only – $50.00
AR Upper and Lower Receivers Only – up to 4 color camo
+ Stencil charge (Stripped) – $225.00+
Upper / Lower / and Handrail One Color – $155.00
Upper/ Lower/ Handrail – up to 4 color camo (
Stripped) – $350.00+
Barrel – one color $70.00
2 Color Fluted Barrel – $100.00
Stock: Standard A2 or M4 (One Color) $45.00
Stock: Target Adjustable (MagPul, etc) One Color
$70.00
Bolt ( Micro Slick) $25.00
Bipod (One Color) $50.00
Forearm – Rail Type (One Color) $55.00
Forearm – Picatinny Quad Rail (One Color) $75.00
Magazines – $25.00 each one color
Extra Color Charges for Accessories (Each Color)
$15.00
AR-10 and Variants Surcharge – add to AR-15 pricing
$50.00
FN-FAL and HK-G3/G33, etc Surcharge – add to AR-15
pricing $50.00
BOLT ACTION RIFLES-COMPLETE
Rem 700 and similar: One Color – $190.00
Barreled Action Only – 120.00
With Adjustable Tactical Stocks – Surcharge: add to
above $25.00
Bolt Action and Tactical 2nd Color surcharge – add
$30.00
Bolt Action and Tactical – Three Color Camouflage
Surcharge – add $75.00 to the 2nd color surcharge
Bolt Action and Tactical – Camouflage Four and Five
Color Patterns – Surcharge (add to one color base price) $125.00
AR-30 and similar .338 Lapua and .408 CheyTac bolt
action rifles – one color $275.00
Bolt Action Rifle Magazines – One Color $20.00
Bolt Action Rifle Magazines – Each Additional Color
$10.00
50 BMG Bolt Action Rifles – One Color $350.00
Barrett 82A1 and similar semi-auto 50BMG rifles – One
Color $500.00
50 BMG Rifles Additional Colors – Each color, add
$100.00
Barrett 82A1 Magazines, ea – One Color $35.00
Barrett and 50 BMG Magazines – Additional Colors,
each: $10.00
Four and Five Color Camouflage Patterns – Surcharge
for .338 Lapua Tactical and 50 BMG rifles: – $250.00
SPECIAL WEAPONS:
Suppressor – $65.00
Edged Weapons: CALL
OTHER SERVICES
Pitting Sand and Fill $50-$100 Depending on
Condition
TUMBLERS – Yeti and RTIC type
One color and simple logo or text – 30.00
Add distress + 10.00
Multi Color tumblers MUST be distressed
At Green Dragon Guns, we always offer a 10% discount
for military and law enforcement on work performed only.
*NOTE: Prices are subject to change without prior
written notice. Not all firearms are the same and sometimes special circumstances may apply Green Dragon Guns will notify the owner of special requirements upon receipt and inspection of the firearm
and provide a revised quote before services are performed.
Tight Tolerance Parts and Markings:
We do not coat sears, springs, bores/chambers or other
tolerance critical or high-flex parts. In addition, we do not media blast scopes or other optics and, as a result, there will not be as good an adhesion of the Cerakote to those items.
TOLERANCE: For standard firearms applications it is often inadvisable to coat both pins and pin holes, as the resulting one (1) mil thickness of the coating when
applied to rounded surfaces creates increase of two (2) mil to the part tolerance and four (4) mil (.004) when both hole and pin are coated. This is also applicable to auto-pistol slide and frame
fit, such as on tight-fitting 1911’s. We typically plug or mask holes and pins and only coat the pin ends. However, we can coat pins and holes and then custom fit these parts after coating for an
additional charge. We recommend hand fitting and lapping for 1911 pistol slides and frames as this will yield a precision fit and can help to tighten looser fitting slide/frame combos.
MARKINGS: For receivers, frames, slides, Picatinny rails which have painted on or lightly laser etched markings these markings will be lost during the surface
preparation and coating unless they are machine engraved or stamped. If these markings are of great importance we can mask over them, but those areas in and immediately around the markings will not
be coated and, as such, will not blend. Manufacturer’s serial numbers will be masked at no additional charge where needed or coated where possible. Some manufacturer model numbers, name etc which are
laser engraved will be masked over. This is per BATFE (ATF) regulations. Please consult us for specific requirements.
Cerakote H-Series: H-Series is the most durable of the standard Cerakote family of coatings and provides the best performance in hardness, wear and scratch
resistance, adhesion and rust resistance. It can withstand heat up to 500f – 600f degrees and comes in the widest range of colors. Therefore, we use the H-Series wherever possible. However, it’s a
two-part heat cure finish and, therefore, cannot be applied to optics and other items or substrates which cannot, or should not be cured at the required temperatures.
Cerakote™ C-Series: For high-temp applications up to 1700°, such as suppressors and machinegun barrels, Cerakote™ C-Series has no equal. It’s available in a wide
range of colors to match the overall finish requirement of the firearm or weapons system. We also use C-Series to coat scopes and other optics, as well as fiberglass and items and substrates which
cannot be baked. It is not as durable as the H-Series and is less scratch and wear resistant. The primary application is optics, electronics and fiberglass stocks which cannot be hear cured.
Cerakote DFAC™ (Dry Film Anti-Carbon) Is a dry film ceramic coating with special properties and attributes specially suited to tight tolerance applications and
high-wear internal parts, such as bolts, bolt carriers, barrels and 1911 barrel bushings, etc… Cerakote DFAC™ penetrates the metal substrate and therefore adds minimal (.25 to .50 mil) thickness.
DFAC™ came out of NIC’s industry leading Micro Dyne automotive and turbine coatings division where it has been used successfully for many years to coat automotive pistons, cylinder walls and turbine
blades, etc. Cerakote DFAC™ provides outstanding anti-friction and wear-reduction properties and good rust prevention properties. In addition when applied to certain internal firearms parts, helps to
reduce carbon fouling by resisting carbon adhesion, which promotes reduced maintenance, easier cleaning and improved operational reliability. DFAC™ imparts a medium grey to dark grey/black color to
most steel substrates. Its primary purpose is one of functionality rather than aesthetics as the parts will “burnish” over time changing the original coated appearance of the parts while maintaining
the anti-friction and anti-carbon attributes of the coating.
CERAKOTE STANDARD PERFORMANCE METRICS:
RUST RESISTANCE: Cerakote™ finishes have been tested in salt spray and full emersion and have withstood beyond 3,000 hours in salt spray and hundreds of hours in
full emersion testing. These results outperform other finishes by over 10x. This makes Cerakote™ finishes the clear choice for marine environments and other environments subject to high humidity and
salt water environments.
WEAR RESISTANCE: Cerakote™ finishes can withstand over 5,000 (5,212) wear cycles per mil (.0001). The Tabor wear test uses an 8″ abrasive wheel applied to a metal
plate coated with 1 mil thickness of the Cerakote coating. In addition, Cerakote’s Coefficient of Friction is 80% less than stainless steel against stainless steel. So, when one or both moving parts
of a firearm are coated you can expect a significantly longer product duty cycle or service life.
ADHESION: Cerakote finishes have an ASTM D3359 rating of 5B and can withstand a 180° mandrel bend rotation test around a 1/4″ mandrel and a ball bearing impact
test of 160 inch-lbs with no cracking or loss of adhesion. This is significant performance given Cerakote’s 9H pencil hardness, which is the highest hardness rating in the scale.
HARDNESS AND SCRATCH RESISTANCE: ASTM D3363 is a 9H pencil hardness and 6H scratch resistance.
FILM THICKNESS: 1.0 mil (Cerakote DFAC “Dry Film Anti-Carbon” is .25 to .50 mil)
Share
Print 